Back to Blog
Hiring Guides

Minisplit not cooling in Mérida: low on gas or leaking?

10 min read
9 views
November 17, 2026

Refrigerant doesn't get used up: if it's low, there's a leak. Other reasons a minisplit won't cool, what to check yourself, how a technician who finds the leak works, what to send for a quote and what the quote should say.

In November, Mérida gets a break: the first nortes arrive, mornings are cool and the minisplit sits off for days. But afternoons can still be hot, and that's when you switch it on and notice the problem: the unit turns on and the fan blows, but the air doesn't come out cold, or a room that used to cool quickly now takes forever. The first thing many people think, and many technicians offer, is “a gas recharge.”

This guide explains what it really means when a minisplit is “low on gas,” what other causes produce the same symptom, what you can check yourself without opening anything, how a technician who looks for the leak works instead of just topping up, and what the quote should say. November and December are a good time to sort it out: you have room to compare before the strong heat returns.

Refrigerant doesn't get used up: if it's low, there's a leak

A minisplit's refrigerant (what everyone calls “gas”) circulates in a closed loop between the indoor and outdoor units. It isn't consumed with use like the gasoline in a car. If the unit was installed and charged correctly, it should keep the same amount for years.

So when a technician measures and confirms the charge is low, the right question isn't “how much to refill it?” but “where is it leaking from?” A recharge without fixing the leak usually doesn't last: the unit loses refrigerant again, cools poorly again and you pay again. And with a low charge, the compressor, the most expensive part, runs under strain.

A common exception: units that cool poorly from day one because they were installed without pulling a vacuum or with a longer line set and no charge adjustment. In that case the installation needs to be corrected.

Before blaming the gas: other causes of the same symptom

“Not cooling” is a symptom, not a diagnosis. Several faults look the same from the couch, and some are fixed without touching the refrigerant:

What you noticePossible causeWho checks it
Weak airflow and a grey filterDirty filters or indoor coilYou (filters) or an AC technician (deep cleaning)
Normal airflow but lukewarm, outdoor unit silentCompressor or outdoor fan not starting: capacitor, control board or power supplyAC technician; electrician if there's a voltage problem
Cools poorly in the afternoon and the outdoor unit sits in the sun or is boxed inDirty or poorly ventilated condenserAC technician
Ice or frost on the pipes or indoor unitLow charge, clogged filter or weak indoor fanAC technician
Oily stains on the outdoor unit's connectionsRefrigerant leak at flare nuts or brazed jointsAC technician
Cools a small room fine but not the living roomNot enough capacity for the spaceAC technician (assessment)

If the breaker also trips, there's a burning smell or the light blinks an error code, it's a different case: see our guides on when the breaker trips with the minisplit and on minisplits that won't turn on or show an error code.

What you can check yourself in ten minutes

Without opening the unit or touching electrical connections, you can rule out the simple stuff and bring better information to the quote:

  1. Mode and temperature. Check on the remote that it's in cool mode (the snowflake), not fan, dry or auto, and that the set temperature is below the room temperature.
  2. Filters. Lift the front cover of the indoor unit and take out the mesh filters. If they're grey or clogged, wash them with water and mild soap, let them dry in the shade and put them back.
  3. Outdoor unit. With the unit running in cool mode, look at the outdoor unit (without climbing anywhere unsafe). Is the fan turning? Can you hear the compressor, a low, steady hum? If the indoor fan blows but everything outside is still, write it down: it's a key clue for the technician.
  4. Around the condenser. On Mérida rooftops the outdoor unit often ends up surrounded by buckets, planters, leaves or pushed against a parapet. It needs space to release heat. Clear what's in the way around it, without putting your hands or water into the unit.
  5. Signs of a leak. Look at the nuts where the copper pipes enter the outdoor unit. An oily stain or dust stuck in a greasy patch usually means refrigerant is escaping there. If you see ice on the pipes or indoor unit, switch the unit off and let it thaw before the visit.
  6. Nameplate data. The outdoor unit's label usually shows the brand, model, capacity and refrigerant type (for example R-22, R-410A or R-32). Take a photo.

What not to do: buy “recharge” cans without knowing which refrigerant your unit uses, loosen nuts or valves, hose down the unit while it's connected, or leave it running for hours with ice on the pipes “to see if it fixes itself.”

Why leaks show up more in Mérida

No leak is unique to Yucatán, but local conditions help them appear:

  • Heavy use. Many units run most of the year; more hours of vibration wear out the connections.
  • Humidity and salt air. Constant humidity and, in homes near the coast such as Progreso or Chicxulub, salty air corrode coils and connections over time.
  • Poorly made flares. Many leaks appear at the flares (the widened end of the copper pipe tightened with a nut). If they were made with the wrong tool or without proper torque, they can leak from the start or over the months.
  • Exposed line sets. On rooftops and facades, pipe insulation dries out in the sun, cracks and leaves the copper exposed to knocks, water and corrosion.

How a technician who looks for the leak works

A proper visit for a minisplit that isn't cooling looks more like a diagnosis than a refill. Every technician has their own method, but these steps are reasonable and you can ask about them:

  1. General check. Filters, coils, fans, voltage and compressor start-up.
  2. Measurement. With gauges (the set of dials with red and blue hoses) and thermometers, the technician compares pressures and temperatures against what's right for the refrigerant and the day's conditions. That shows whether the charge is low, high or fine.
  3. Leak search. If the charge is low, they look for where it's escaping: soapy water on connections (bubbles give the leak away), an electronic detector, or a nitrogen pressure test in which the system is pressurized and watched for a pressure drop.
  4. Repair. Remaking a flare, replacing a nut or valve, brazing a section or, if the leak is in a pierced coil, quoting its repair or replacement.
  5. Vacuum. Before recharging, air and moisture are pulled out of the loop with a vacuum pump. Skipping it leaves moisture inside that damages the unit.
  6. Correct charge. The refrigerant on the nameplate is charged, ideally weighed on a scale per the manufacturer's amount and the line length, and operation is checked again.

Not every visit needs every step, and some small leaks are hard to find. What matters is that the technician explains what they measured and what they found.

Recharge, repair or replace: questions to decide

When the leak is at an accessible nut, repairing usually makes sense. When it's in the coil, the compressor is damaged or the unit is very old, it's worth comparing with a new one. Ask:

  • Where exactly is the leak and how did you find it?
  • What refrigerant does my unit use? Old R-22 units use a refrigerant that is being phased out; ask whether it's available and how its cost compares with a new unit.
  • Is the compressor fine, or has it run for a long time with a low charge?
  • If I repair it, what warranty do you give on the leak and for how long?

If you end up replacing it, our guide on when to repair and when to install a minisplit helps you compare, and the one on installing a minisplit bought during the sales season explains what to ask for at installation so the problem doesn't repeat.

What to send when asking for a quote

With good information, the technician arrives with the right refrigerant and you can compare quotes. Send:

  • Photos of the outdoor unit's label (brand, model, capacity, refrigerant type) and of the indoor unit.
  • Photos of the outdoor unit's connections, especially if you see oily stains or ice.
  • Exactly what it does: blows lukewarm, cools a little, ices up, the outdoor fan doesn't spin.
  • Since when, and whether it happened suddenly or gradually.
  • How old the unit is, when it was last serviced and whether it has been recharged before.
  • Where the outdoor unit is (rooftop, facade, patio), how high, and whether there's safe access.

If it has already been topped up once or twice this year, say so: it's the clearest clue to an unrepaired leak.

What the written quote should say

ItemWhat to ask forWhy it matters
DiagnosisWhether it's charged separately and credited if you accept the repairAvoids surprises if you decide not to repair
LeakWhere it was found and how (soap, detector, nitrogen)Confirms it isn't a blind recharge
RepairWhat is redone or replaced: nut, flare, brazing, valveLets you compare with another quote
Vacuum and chargeWhether a vacuum is included, which refrigerant and how the amount is measuredA charge without vacuum or “by eye” shortens the unit's life
WarrantyTerm and what it covers if the leak returnsDefines what happens if it cools poorly again

To review how to compare two service quotes, read how to read a quote in Mérida.

Red flags when hiring

  • They offer a “gas recharge” over the phone without having seen or measured the unit.
  • They don't mention finding the leak, pulling a vacuum or which refrigerant your minisplit uses.
  • It's the second or third recharge in a few months and nobody has explained why it leaks.
  • They charge by “pounds of gas” without saying how they measured how much was missing.
  • They want full payment upfront or won't put anything in writing.
  • They say the compressor “is dead” without explaining what they measured, and push to sell you a new unit that same day.

After the repair: how to keep it from happening again

  • Check that the pipes are left fully insulated and protected from the sun; torn insulation on the rooftop is a future leak.
  • Schedule minisplit maintenance before the hot season, not in the middle of a May heat wave when every technician is booked.
  • Keep the outdoor unit clear; if it's very dirty or noisy, see the guide on a dirty or noisy outdoor unit.
  • Keep the quote and the receipt with the date: if it cools poorly again within weeks, you'll have what you need to claim the warranty.

How to find a technician on ContrataYa

On ContrataYa you can search for air conditioning and minisplit technicians in Mérida, review their profiles and ask them for a quote with the photos and details from this guide. If the diagnosis points to a voltage, wiring or breaker problem, you can also search for electricians in Mérida, and for patching or protecting where the pipes pass through walls and parapets, a handyman.

When a profile says Verified, it means the person submitted their ID (front and back) and a bill showing their name and address to the platform. It is not a technical certification, a license or a guarantee of their work. You can read the details in our verification badges policy. Ask for references, a clear explanation of what they measured and a written quote before you accept.

A minisplit that isn't cooling almost never “just needs gas.” With a diagnosis that finds the leak, a well-made repair and a correct charge, it can be ready for the hot season.

Cargando preguntas frecuentes...

Share Article

Need a professional for your project?

Find local pros in Mérida

Find Professionals